Hot Downloads

Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: belkin again

belkin again 8 years 4 months ago #26886

  • dougal
  • dougal's Avatar
  • Offline
  • New Member
  • Posts: 18
  • Karma: 0
hi all

having had problems setting up a belkin wireless modem on my neighbours computer i thought id try setting it up on mine
well i had a week to spare.....
plugged it in to the ethernet port on my computer,plugged in the phone line.
powered it up ,did a factory reset, typed in the ip address ..surprise surprise, nothing...just this page cannot..

any help much appreciated

dougal
my existing modem using usb is fine
The administrator has disabled public write access.

Re: belkin again 8 years 4 months ago #26887

  • dougal
  • dougal's Avatar
  • Offline
  • New Member
  • Posts: 18
  • Karma: 0
ps
i have disabled windows and avg firewalls
The administrator has disabled public write access.

Re: belkin again 8 years 4 months ago #26891

  • Chojin
  • Chojin's Avatar
  • Offline
  • Senior Member
  • Posts: 251
  • Karma: 0
Already tried to read the manual?! :)
CCNA / CCNP / CCNA - Security / CCIP / Prince2 / Checkpoint CCSA
The administrator has disabled public write access.

Re: belkin again 8 years 4 months ago #26892

  • dougal
  • dougal's Avatar
  • Offline
  • New Member
  • Posts: 18
  • Karma: 0
yes all ninety pages of it,
trouble is there is nothing to set up. the router does not show in any of the modem /internet options on my computer or device manager- xp service pack 2
regards dougal
The administrator has disabled public write access.

Re: belkin again 8 years 4 months ago #26894

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Posts: 1577
  • Thank you received: 7
  • Karma: 3
I haven't read your previous post completely. So I'd start with asking: Do you have the drivers CD for the router? What happened when you install it?

When you connected your router to your PC's ethernet port, does the LEDs come up, do you see it blinking?. If NOT, you probably need a crossover cable.

Second, If you could NOT get the driver, usually those routers have a web interface were you can configure it from. And some times there is a default IP/Mask already setup on your belkin. Seek the manual to get the IP/Mask. Then set your PCs Ethernet interface (Local Area Connection) IP to a different IP on the same subnet. For example:

Say the belkin's IP/mask was 192.168.1.1 / 255.255.255.0

Configure your (Local Area Connection) to: 192.168.1.2 / 255.255.255.0

Now go to your web browser and type the IP of the belkin (192.168.1.1) in the address bar. If all is well you should see the web interface of the belkin showing up to you.

Hope some thing here helps
Studying CCNP...

Ammar Muqaddas
Forum Moderator
www.firewall.cx
The administrator has disabled public write access.

Re: belkin again 8 years 4 months ago #26897

  • dougal
  • dougal's Avatar
  • Offline
  • New Member
  • Posts: 18
  • Karma: 0
thanks solo
there is no installation disc available for this router, evrything is done through the ip address so basically if that dosent connect the whole thing meets a brick wall .
will try your suggestions and get back.
regards
dougal
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Time to create page: 0.082 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup