Hot Downloads

×

Notice

The forum is in read only mode.
Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: commands

commands 7 years 2 months ago #37229

  • sais
  • sais's Avatar Topic Author
  • Offline
  • Frequent Member
  • Frequent Member
  • Posts: 59
  • Thank you received: 0
can brief desribe wat is purpose o this command used in 3560 switch

spanning-tree mode pvst

spanning-tree extend system-id

no spanning-tree vlan 88


interface Port-channel1

switchport trunk encapsulation dot1q

switchport trunk native vlan 87

Re: commands 7 years 1 month ago #37231

  • Nevins
  • Nevins's Avatar
  • Offline
  • Expert Member
  • Expert Member
  • Posts: 438
  • Karma: 4
  • Thank you received: 9
[code:1]spanning-tree mode pvst [/code:1]

Per vlan spanning tree was enabled which mean per lan group (vlan) you have segmented in your network into more then one loop redundancy (spanning tree) groups.

[code:1]
no spanning-tree vlan 88 [/code:1]

states that loop protection is disabled on that vlan and no spanning-tree is taking place

[code:1]
interface Port-channel1

switchport trunk encapsulation dot1q

switchport trunk native vlan 87[/code:1]


This code states that on Port-channel1 vlan 87 will act as the native vlan meaning if any frames are not tagged into a specific vlan it will default to vlan 87.


www.cisco.com/warp/public/473/spanning_tree1.swf

Explains spanning tree very well. Per vlan spanning-tree is only different in that it blocks sets blocking states per vlan not per trunk link. (trunking still must be enabled)


Edit: I could be a bit more descriptive but I have a job interview to go to at 3pm it's 12:00 noon. If you have any more questions after viewing the flash about spanning tree I would be glad to help explain.

Re: commands 7 years 1 month ago #37232

Best of lick for the interview and thanks for the flash link.

Re: commands 7 years 1 month ago #37233

Nevins,

The link you have send for STP was really execellent. I was trying to find some more links on different topics, but it didn't allowed me to access. Always getting an error "session expired".
is it possible for you to provide some more links on different topics (especially on switches).

Thanks[/u][/i]

Re: commands 7 years 1 month ago #37235

  • Nevins
  • Nevins's Avatar
  • Offline
  • Expert Member
  • Expert Member
  • Posts: 438
  • Karma: 4
  • Thank you received: 9
www.firewall.cx/ftopict-7477-.html

I tried to make a repository there a while back and get more people to plug into it but it never really took off.

Re: commands 7 years 1 month ago #37238

  • sais
  • sais's Avatar Topic Author
  • Offline
  • Frequent Member
  • Frequent Member
  • Posts: 59
  • Thank you received: 0
thank you . the link u have given is more useful. if u have some link related ethernth group, and switch related topics send me ok.
  • Page:
  • 1
Time to create page: 0.171 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup