Hot Downloads

Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: boot problem

boot problem 5 years 7 months ago #36813

  • bkash
  • bkash's Avatar
  • Offline
  • Frequent Member
  • Posts: 32
  • Karma: 0
my 2008 server booting problem.
it's gone to safe mode but when gone to normal mode it's comes to pshyciscl blue screen error.
The administrator has disabled public write access.

Re: boot problem 5 years 7 months ago #36825

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Posts: 1577
  • Thank you received: 7
  • Karma: 3
I'd first do a scandisk for logical errors and bad clusters. Go to safe mode (or recovery mode using the Windows CD), then command prompt and type:

chkdsk c: /r

If the problem persists after you do this, then it could be a driver/hardware issue. Try disconnecting all USB and any external devices. Tell us what happens.
Studying CCNP...

Ammar Muqaddas
Forum Moderator
www.firewall.cx
The administrator has disabled public write access.

Re: boot problem 5 years 7 months ago #36827

  • rizin
  • rizin's Avatar
  • Offline
  • Distinguished Member
  • Posts: 203
  • Karma: 0
Hi bkash,

1. Is it running server or newly installed server.

2. Have you check all the compatible hardware requirements for Installing Server 2008 (ignore if it is already running server)

3. Check for the malfunction/conflict any applications running on server other than Operating system software (ignore if it is New installed server)

4. Check for the RAM Module, replace and reconnect the RAM and also make sure RAM is defective or not (Apply for both newly installed and running windows 2008 server)

5. Check for other hardware conflicts.

Do the above tests and get back to us for feed back.

Good Luck !

Rizin
Known is a drop, unknown is an Ocean
The administrator has disabled public write access.

boot 5 years 7 months ago #36830

  • bkash
  • bkash's Avatar
  • Offline
  • Frequent Member
  • Posts: 32
  • Karma: 0
hi, S0lo
i have tried chkdsk in safe mode
and also try to repair from 2008 cd but nothing process.
not used any usb. this is running server.
The administrator has disabled public write access.

boot 5 years 7 months ago #36831

  • bkash
  • bkash's Avatar
  • Offline
  • Frequent Member
  • Posts: 32
  • Karma: 0
hi,
rizin
this is running server.
i have checked all RAM or other hardware new install as like also check to disable nic card driver
also check ram error but not found any error
how could i check windows error log to find out any clue..
The administrator has disabled public write access.

Re: boot problem 5 years 7 months ago #36832

  • rizin
  • rizin's Avatar
  • Offline
  • Distinguished Member
  • Posts: 203
  • Karma: 0
Would you mind give me the blue screen error code number.

1. Well, as you said you can able to go into safe mode, Log in to the server, start > run > eventvwr.msc. You will taken to event viewer, there check for the system error, application errors and get the event ID or go for microsoft online help or get back to us with that Event ID it is better you can make it your system errors, applications errors into zip and upload it here.

Note : Try to uninstall Anti - Virus software from server for time being however be careful, if you are not confident let it as it was, just do the above steps.

Good Luck,

Rizin
Known is a drop, unknown is an Ocean
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Time to create page: 0.079 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup