Hot Downloads

Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: Is there ONE Command to enable full duplex in Cisco 2960

Is there ONE Command to enable full duplex in Cisco 2960 5 years 6 months ago #36578

  • rizin
  • rizin's Avatar
  • Offline
  • Distinguished Member
  • Posts: 203
  • Karma: 0
Hi All,

How to enable Full Duplex in all the ports of Cisco 2960 in ONE Command. Also without connecting to console is there any way to connect Cisco 2960 when it is in unmanaged status.

Looking forward your reply, Thanks in Advance.

Rizin
Known is a drop, unknown is an Ocean
The administrator has disabled public write access.

Re: Is there ONE Command to enable full duplex in Cisco 2960 5 years 6 months ago #36587

  • TheBishop
  • TheBishop's Avatar
  • Offline
  • Moderator
  • Posts: 1719
  • Thank you received: 8
  • Karma: 5
Not quite; but I think you can do it in two. For example:
interface range fa0/1 - 24
duplex full
The administrator has disabled public write access.

Re: Is there ONE Command to enable full duplex in Cisco 2960 5 years 6 months ago #36613

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Posts: 1577
  • Thank you received: 7
  • Karma: 3
Also without connecting to console is there any way to connect Cisco 2960 when it is in unmanaged status.

If you mean you want to configure the switch without using console, then most of those switch models have a web interface (device manager), you need the command ip http server. If this is what you need, I can give you further info if you want.
Studying CCNP...

Ammar Muqaddas
Forum Moderator
www.firewall.cx
The administrator has disabled public write access.

Re: Is there ONE Command to enable full duplex in Cisco 2960 5 years 6 months ago #36649

  • rizin
  • rizin's Avatar
  • Offline
  • Distinguished Member
  • Posts: 203
  • Karma: 0
Sorry for the late reply folks,

2960 is connected to the lan network 192.168.1.0 network, My PC is connected to the same network, In this case can i able to access 2960 without configuring it, i guess by default 2960 switch is in the unmanaged state. so in this case ip also not been configured. considering above suitation how can i access 2960 switch from my PC.

Thanks Much !
Known is a drop, unknown is an Ocean
The administrator has disabled public write access.

Re: Is there ONE Command to enable full duplex in Cisco 2960 5 years 5 months ago #36651

  • TheBishop
  • TheBishop's Avatar
  • Offline
  • Moderator
  • Posts: 1719
  • Thank you received: 8
  • Karma: 5
I suppose a console cable is out of the question?
The administrator has disabled public write access.

Re: Is there ONE Command to enable full duplex in Cisco 2960 5 years 5 months ago #36654

  • rizin
  • rizin's Avatar
  • Offline
  • Distinguished Member
  • Posts: 203
  • Karma: 0
hi.

sorry to say that I prefer not to use Console and i would like to know it for my learning purposes.

Thanking you in advance for your help.

Rizin
Known is a drop, unknown is an Ocean
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Time to create page: 0.079 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup