Hot Downloads

×

Notice

The forum is in read only mode.
Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: dns-server /dhcp pool

dns-server /dhcp pool 12 years 8 months ago #13481

Hi,

I wonder if i may run a few questions past you guys. We have a Cisco 1700 at one of our sites which is supposed to be managed but due to problems with the third party company i had to go there to perform some work.

I wanted to add in a dns server ip. Because i don't have the enable secret (Third PTY won't tell us) i used the break command normally used for password recovery. then once in used "copy start run".

Q. can i make config changes this way, save the changes then switch the config-register back and reload?

I managed to make the changes - Dhcp pool - dns-server ip's, right? changed the config-reg back and reloaded. No connectivity. anyway i messed around with different ip's eventually put it back to to original powered of for 5 mins and on again and it was ok.

Q: have i missed something out?

Q: could reloading or powering off and on to quickly affect thigs?

Q: Could the router be downloading it's config or something additional from a TFTP server? Is there anything i can check to confirm this on the config?

This is the dns part of the config all i want to do is change 1.0.84.187 for 84.33, should be simple?

ip dhcp pool 0
network 172.16.0.0 255.255.0.0
default-router 172.16.0.15
dns-server 1.0.84.8 1.0.84.187 158.152.1.43 158.152.1.58
domain-name parkside.net
lease infinite

Q: Is this part saying that 1.0.84.187 and 158.152.1.43 are not being used for dns?

no ip domain lookup
ip name-server 1.0.84.187
ip name-server 158.152.1.43
ip cef
no scripting tcl init
no scripting tcl encdir

Sorry i know thats long winded. Any help on any part of my problem would be much appreciated.

Kind regards
J mac
Kind Regards
J Mac

Re: dns-server /dhcp pool 12 years 8 months ago #13494

  • Tarun
  • Tarun's Avatar
  • Offline
  • Distinguished Member
  • Distinguished Member
  • Posts: 138
  • Thank you received: 0

Q. can i make config changes this way, save the changes then switch the config-register back and reload?


Yes.

I managed to make the changes - Dhcp pool - dns-server ip's, right? changed the config-reg back and reloaded. No connectivity. anyway i messed around with different ip's eventually put it back to to original powered of for 5 mins and on again and it was ok.

Q: have i missed something out?


No as per your description.

Q: could reloading or powering off and on to quickly affect thigs?


Just a coincidence i would say.

Q: Could the router be downloading it's config or something additional from a TFTP server? Is there anything i can check to confirm this on the config?


Not sure if there is any such command that id ont know of.

This is the dns part of the config all i want to do is change 1.0.84.187 for 84.33, should be simple?

ip dhcp pool 0
network 172.16.0.0 255.255.0.0
default-router 172.16.0.15
dns-server 1.0.84.8 1.0.84.187 158.152.1.43 158.152.1.58
domain-name parkside.net
lease infinite

Q: Is this part saying that 1.0.84.187 and 158.152.1.43 are not being used for dns?


Sorry, no idea about this one.

Hope to see replies from others regarding the same... :wink:
Next would be SP (Service Provider)
CCNA, CCNP (Switching), CCIE#20640

Re: dns-server /dhcp pool 12 years 8 months ago #13498

Hey thanks a lot for the speedy reply that's really helpful. Hopefully others may be able to shed a little on the latter part.
Kind Regards
J Mac
  • Page:
  • 1
Time to create page: 0.164 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup