Hot Downloads

×

Notice

The forum is in read only mode.
Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: when upgrading ios ....

when upgrading ios .... 6 years 10 months ago #37532

  • sais
  • sais's Avatar Topic Author
  • Offline
  • Frequent Member
  • Frequent Member
  • Posts: 59
  • Thank you received: 0
when upgrading ios . tftp installed in pc. am not able to ping router to tftp & also pc to router issue. firewall all turned off .......in switch 3560-8port .ip
int vlan1
ip -192.168.10.1

in pc:

gateway 192.168.10.1
pc ip 192.168.10.10 ,.

wat will issue ? and also in tftp server am getting only message tftp server started .that all ? hw solve issue ????

Re: when upgrading ios .... 6 years 10 months ago #37535

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Moderator
  • Posts: 1577
  • Karma: 3
  • Thank you received: 7
It seams that your using the same IP for both vlan1 and the gateway. They should be different. (I'm assuming vlan1 here is on the 3560 switch).

Re: when upgrading ios .... 6 years 10 months ago #37536

  • sais
  • sais's Avatar Topic Author
  • Offline
  • Frequent Member
  • Frequent Member
  • Posts: 59
  • Thank you received: 0
yaa . vlan in 3560 switch.

Switch#copy tftp flash
Address or name of remote host []? 192.168.10.10
Source filename []? c3560-ipbasek9-mz.122-55.SE1.bin ?
Destination filename [c3560-ipbasek9-mz.122-55.SE1.bin]?
Accessing tftp://192.168.10.10/c3560-ipbasek9-mz.122-55.SE1.bin...
%Error opening tftp://192.168.10.10/c3560-ipbasek9-mz.122-55.SE1.bin before this was error .
now facing new prblm. that i already remove ios image . so no ios in switch . now switch is switch : mode.

switch: copy xmodem:usef flash:c3560-ipservicesk9-mz.150-1.SE(1).bin

: boot.error copy image
ast step its show err

Re: when upgrading ios .... 6 years 10 months ago #37537

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Moderator
  • Posts: 1577
  • Karma: 3
  • Thank you received: 7
This document might help: www.cisco.com/en/US/products/hw/switches...186a0080169696.shtml

But it uses Xmodem which is very slow, there is a section at the last which shows you how can you speed it up.

Re: when upgrading ios .... 6 years 9 months ago #37538

  • sais
  • sais's Avatar Topic Author
  • Offline
  • Frequent Member
  • Frequent Member
  • Posts: 59
  • Thank you received: 0
thank you solo:
i followed same step .am getting last message error loading image.

i tired many time different ios ? prblm same ? i have no idea. even senior tired .

i want create id in cisco.com. so that i can download ios.? it not possible
? can u assist me .....

Re: when upgrading ios .... 6 years 9 months ago #37539

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Moderator
  • Posts: 1577
  • Karma: 3
  • Thank you received: 7
I'm assuming you have enough flash memory left in your switch to load the IOS. If not, try to remove any big old IOS files that you don't need from the flash.

Could you copy/paste the whole recovery here including the error messages, so that we can see whats happening.
  • Page:
  • 1
  • 2
Time to create page: 0.145 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup