Hot Downloads

Welcome, Guest
Username: Password: Remember me

TOPIC: 1720 Router--ADSL--pvcmode

1720 Router--ADSL--pvcmode 7 years 9 months ago #28482

  • mic
  • mic's Avatar
  • Offline
  • Frequent Member
  • Posts: 28
  • Karma: 0
help please, i have a :( wic, with the version that supports pppoe and pvc commands, it was working fine and able to get into and configure th vc-mode (atm-vc-if) commands , i did a reload and lost all vc mode commands , does anyone know how i can get this back, is it done bye commands or do i have to download something for it to come back, like i said it was able to do all before i did a reload, please anyones help wound be great?? thanks alot mic
The administrator has disabled public write access.

Re: 1720 Router--ADSL--pvcmode 7 years 9 months ago #28483

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Posts: 1577
  • Thank you received: 7
  • Karma: 3
Were you able to reload before and pertain the same commands?. Or have you just added these commands and this is the first time you reload after adding them?. In the second case, you may have forgot to save your config by copy run start. which means that you probably lost it unless you have a backup file on your flash or some thing.
Studying CCNP...

Ammar Muqaddas
Forum Moderator
www.firewall.cx
The administrator has disabled public write access.

Re: 1720 Router--ADSL--pvcmode 7 years 9 months ago #28505

  • mic
  • mic's Avatar
  • Offline
  • Frequent Member
  • Posts: 28
  • Karma: 0
right i did not copy run start ( dummy i am ). and lost it, but was able to do commands before reload, just trying to get vc mode and dsl commands back, someone said there is a reset button on the wic for loop back, Have you every heard of that ?? thanks mic

here is the show version after reload
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-K2SY7-M), Version 12.1(5)YB4, EARLY DEPLOYMENT RE
LEASE SOFTWARE (fc1)
TAC Support: www.cisco.com/tac
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Tue 03-Jul-01 19:41 by ealyon
Image text-base: 0x800080E0, data-base: 0x80B3540C

ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-K2SY7-M), Version 12.1(5)YB4, EARLY DEPLOYMENT RELEAS
E SOFTWARE (fc1)

Router uptime is 2 days, 8 hours, 36 minutes
System returned to ROM by power-on
System image file is "flash:C1700-K2SY7-MZ.123-7.bin"

cisco 1720 (MPC860) processor (revision 0x601) with 24576K/8192K bytes of memory
.
Processor board ID JAD051707U5 (4023631964), with hardware revision 0000
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
--More--
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
The administrator has disabled public write access.

Re: 1720 Router--ADSL--pvcmode 7 years 9 months ago #28515

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Posts: 1577
  • Thank you received: 7
  • Karma: 3
someone said there is a reset button on the wic for loop back, Have you every heard of that ?? thanks mic

No, Although I'm not the expert in this but I don't think it's going to return your lost commands since the commands are stored in NV-RAM which has nothing to do with the WIC hardware.
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

The configuration register is set to 0x2102. Which is the correct default setting to load the router normally using flash and NV-RAM. It seams that your problem is really just a matter of bad luck that you forgot to copy run start.

I guess the only backup is your own memory. Good luck ;)
Studying CCNP...

Ammar Muqaddas
Forum Moderator
www.firewall.cx
The administrator has disabled public write access.
Time to create page: 0.080 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup