Hot Downloads

Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: how to connect 2 different IP Address

how to connect 2 different IP Address 8 years 3 months ago #27034

Hello guys,

I have problem in connecting 2 different IP Address.
I have 192.168.18.0/24 and 192.168.1.0/24 they are connected to DLINK 3326SRM Switch. How can I connect host computer from 192.168.18.0/24 to 192.168.1.0/24 and vice versa.

What will be the routing table in DLINK 3326SRM?

Thank you in advance.
The administrator has disabled public write access.

Re: how to connect 2 different IP Address 8 years 3 months ago #27036

  • SteveP
  • SteveP's Avatar
  • Offline
  • Distinguished Member
  • Posts: 161
  • Karma: 0
They're two separate networks so you can't connect them via a switch. You'll have to use a router or reassign the addresses to be in the same network. I'm not familiar with the switch that you're using.
The administrator has disabled public write access.

Re: how to connect 2 different IP Address 8 years 3 months ago #27038

The switch is a layer 3 switch.

Is there any way to connect the two networks?
The administrator has disabled public write access.

Re: how to connect 2 different IP Address 8 years 3 months ago #27040

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Posts: 1577
  • Thank you received: 7
  • Karma: 3
The switch is a layer 3 switch.

Is there any way to connect the two networks?

Sure there is if it is a layer 3. Not sure how to configure D-link's though, If you need the manual for this model, it's here: www.retrevo.com/support/D-link-DES-3326S...ual/id/420bh240/t/2/
Studying CCNP...

Ammar Muqaddas
Forum Moderator
www.firewall.cx
The administrator has disabled public write access.

Re: how to connect 2 different IP Address 8 years 3 months ago #27042

  • Elohim
  • Elohim's Avatar
  • Offline
  • Senior Member
  • Posts: 220
  • Karma: 0
If it's a layer 3 switch, assign the respective ports to different VLANs and assign IP addresses to the VLAN interface and you will have connectivity between the subnetworks. You need to set the default gateway on the PCs to the IP address of the VLAN interface.
The administrator has disabled public write access.

Re: how to connect 2 different IP Address 8 years 3 months ago #27043

  • S0lo
  • S0lo's Avatar
  • Offline
  • Moderator
  • Posts: 1577
  • Thank you received: 7
  • Karma: 3
Ooops :oops:, I said you needed RIP or OSPF, that is incorrect. Elohim is right. Don't know what got in my head!!
Studying CCNP...

Ammar Muqaddas
Forum Moderator
www.firewall.cx
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Time to create page: 0.081 seconds

CCENT/CCNA

Cisco Routers

  • SSL WebVPN
  • Securing Routers
  • Policy Based Routing
  • Router on-a-Stick

VPN Security

  • Understand DMVPN
  • GRE/IPSec Configuration
  • Site-to-Site IPSec VPN
  • IPSec Modes

Cisco Help

  • VPN Client Windows 8
  • VPN Client Windows 7
  • CCP Display Problem
  • Cisco Support App.

Windows 2012

  • New Features
  • Licensing
  • Hyper-V / VDI
  • Install Hyper-V

Linux

  • File Permissions
  • Webmin
  • Groups - Users
  • Samba Setup